DIY: Skipt um gorm að aftan í E53 X5

Hérna getur þú varpað fram spurningum um tæknilega hluti eða þá deilt visku þinni með hinum um BMW.

DIY: Skipt um gorm að aftan í E53 X5

Postby rockstone » Sun 06. Mar 2016 21:26

Þar sem ég fann engar upplýsingar á netinu um þetta, þá bjó ég þær til.

As I found literally nothing on the internet regarding this subject, I decided to take photos while I replaced mine.

Disclamer: I am not responsable for anyone that decides to use this information. Use this information at your own risk.


First, Jack up the car and remove the wheel:
ImageImage

Remember to put a jackstand, I put mine undir the rear subframe, then lover the jack.
Image

Next jack under the rear till there is no stress on the strut and remove the lower bolt.
ImageImage

Next you need to remove the rear upper wishbone, first release the wiring and brake pipe for the holders.
ImageImage

Loosen the nut and the bolt that holds the wishbone.
ImageImageImage

Then the upper rear wishbone can be removed.
Image

Time to remove the spring. To remove it since there is no space for spring clamps, I jacked under the hole thing till the spring was as compressed as i could get it, then chained it to holt it like that. That way when i released the jack the spring was a bit looser, and with a crowbar, got it out.
ImageImage

Then to take the chains off the old spring, I used spring clamps.
ImageImage

Then did the whole thing backwards, for the installation of the new spring.
ImageImageImage
ImageImageImage
Image
User avatar
rockstone
Formúlubílstjóri
 
Posts: 5217
Joined: Thu 17. Apr 2008 23:20
Location: HérogÞarogAllstaðar

Re: DIY: Skipt um gorm að aftan í E53 X5

Postby Zed III » Sun 06. Mar 2016 21:29

þetta er furðuleg leið. Þegar ég convertaði í gorma úr púðum hjá mér var þetta næstum eins og að skipta um gorma í e30.

Var þetta svona þröngt hjá þér ?
Benedikt Guðmunds. 615-2630
The Small : BMW Z3 '97 , The Big : BMW X5 4.4i us '00 & The Beater : BMW X5 4.4i '01

Image
User avatar
Zed III
Formúlubílstjóri
 
Posts: 4849
Joined: Thu 08. May 2008 22:17
Location: Hfj City

Re: DIY: Skipt um gorm að aftan í E53 X5

Postby rockstone » Sun 06. Mar 2016 21:36

Zed III wrote:þetta er furðuleg leið. Þegar ég convertaði í gorma úr púðum hjá mér var þetta næstum eins og að skipta um gorma í e30.

Var þetta svona þröngt hjá þér ?


Þar sem ég vildi ekki losa neitt sem tengist hjólastillingu bílsins þá gerði ég þetta svona.
User avatar
rockstone
Formúlubílstjóri
 
Posts: 5217
Joined: Thu 17. Apr 2008 23:20
Location: HérogÞarogAllstaðar

Re: DIY: Skipt um gorm að aftan í E53 X5

Postby Zed III » Mon 07. Mar 2016 08:50

rockstone wrote:
Zed III wrote:þetta er furðuleg leið. Þegar ég convertaði í gorma úr púðum hjá mér var þetta næstum eins og að skipta um gorma í e30.

Var þetta svona þröngt hjá þér ?


Þar sem ég vildi ekki losa neitt sem tengist hjólastillingu bílsins þá gerði ég þetta svona.


Held ég hafi losað eina ballance stöng hjá mér, ekkert sem kemur nálægt hjólastillingunni.

Efa það ekki að þetta hafi þó þurft hjá þér, þú ert nú betri í þessum hlutum en ég :thup: :thup:
Benedikt Guðmunds. 615-2630
The Small : BMW Z3 '97 , The Big : BMW X5 4.4i us '00 & The Beater : BMW X5 4.4i '01

Image
User avatar
Zed III
Formúlubílstjóri
 
Posts: 4849
Joined: Thu 08. May 2008 22:17
Location: Hfj City


Return to Tæknilegar umræður

Who is online

Users browsing this forum: No registered users and 13 guests